| Availability: | |
|---|---|
| Quantity: | |
ZSJH
Seamless steel line pipe is manufactured without a longitudinal weld seam for oil and gas gathering, transmission and related facility piping. It is specified by steel grade, product specification level (PSL), outside diameter, wall thickness and delivery condition to match the pipeline design.
ZSJHSTEEL supports procurement to agreed requirements, including beveled ends, external corrosion protection, inspection documents and material traceability.
| Parameter | Specification / Ordering Requirement |
|---|---|
| Product | Seamless carbon or low-alloy steel line pipe |
| Product Standard | API 5L or another agreed specification, with edition identified |
| Steel Grade | Grade B or specified X grade, subject to supply confirmation |
| Product Specification Level | PSL 1 or PSL 2, as required |
| Delivery Condition | Applicable condition and grade suffix to be specified |
| Outside Diameter | Actual OD in mm, or nominal size with dimensional reference |
| Wall Thickness | Specified thickness in mm and applicable tolerance |
| Length | Fixed or random lengths, as agreed |
| Pipe Ends | Plain or beveled ends according to the specification |
| Surface Protection | Temporary protection or specified external coating |
| Inspection | Material, dimensional, hydrostatic and nondestructive testing as required |
| Documentation | Material certificate, inspection records and traceability information |
Recommended ordering format:
Standard + Grade + PSL + Delivery Condition + OD × Wall Thickness × Length + End Preparation + Coating + Inspection Requirements.

Grade B and X grades such as X42, X52 and X65 are examples of line-pipe material designations. They identify different strength requirements; actual supply availability must be confirmed.
Grade selection should consider:
Design pressure and temperature.
Required wall thickness and corrosion allowance.
Toughness and fracture-control requirements.
Welding and fabrication requirements.
Conveyed fluid and service environment.
A higher-strength grade is not automatically the best choice. Material selection must match the design, installation conditions and project specification.
For sour service, low-temperature duty or other demanding conditions, specify the additional material and testing requirements explicitly.
PSL means Product Specification Level. It is separate from steel grade.
| Level | Procurement Focus |
|---|---|
| PSL 1 | Requirements under the selected standard for the specified grade and product |
| PSL 2 | Additional controls on chemistry, mechanical properties, toughness, testing and traceability, as applicable |
Specify both the grade and PSL rather than ordering by “API 5L pipe” alone. The exact requirements depend on the standard edition, grade, dimensions and delivery condition.
PSL 2 is not a pressure class and does not automatically establish suitability for sour service. Required supplementary provisions and acceptance criteria must also be stated.
Seamless line pipe is commercially specified across different grades and PSL levels, with separate options for demanding service conditions.
Outside Diameter — OD
Controls fit-up with connecting pipework, fittings and equipment. DN and NPS are nominal designations and should not be treated as measured diameters.
Wall Thickness — WT
Affects pipe weight, bore and the thickness available for design calculations. Include the applicable tolerance and any project-specific minimum requirements.
Length — L
Specify fixed or random lengths, permitted tolerances and quantities. A pipe tally may be requested for delivery planning and material control.
Beveled Ends
Prepare the pipe for field-welded joints. Confirm bevel angle, root face, end squareness and any special preparation required by the welding procedure.
Pipe pressure suitability depends on the design code, dimensions, material properties, temperature and allowances. It cannot be determined from steel grade or PSL alone.
Select external protection according to installation conditions, operating temperature, handling and the corrosion-control design.
| Finish / Coating | Purpose & Ordering Considerations |
|---|---|
| Bare or Temporarily Protected | Protection for storage and transport; not a complete buried-service coating system |
| Fusion-Bonded Epoxy — FBE | Specify coating requirements, service conditions and acceptance tests |
| Three-Layer Polyethylene — 3LPE | Epoxy, adhesive and polyethylene layers; specify thickness, cutback and inspection requirements |
| Three-Layer Polypropylene — 3LPP | Specify suitability for the project temperature and installation conditions |
Coating availability is subject to confirmation. ISO 21809-1 addresses plant-applied external three-layer polyethylene and polypropylene coatings for pipeline transportation systems within its scope.
For coated pipe, agree surface preparation, coating thickness, holiday testing, adhesion requirements, end cutback and repair procedures. Field-joint protection must also be coordinated with the factory coating.
External coating does not protect against internal corrosion. Internal corrosion control and cathodic protection, where applicable, remain part of the project design.

A traceability system should connect the delivered pipe to its manufacturing and inspection records.
| Check / Record | Purpose |
|---|---|
| OD, Wall Thickness & Length | Verify dimensional conformity |
| End Geometry & Surface Inspection | Assess fit-up and visible condition |
| Chemical Analysis | Verify the specified material composition |
| Mechanical & Toughness Tests | Confirm properties required by the order |
| Hydrostatic Testing | Meet the applicable pipe-standard requirements |
| Nondestructive Examination | Verify the specified method, coverage and acceptance criteria |
| Coating Inspection | Confirm agreed coating quality where supplied |
| Heat / Pipe Identification | Link products to corresponding records |
The inspection scope must be agreed before production. Hydrostatic testing and nondestructive examination address different requirements; one should not be assumed to replace the other.
For pipe that is coated or cut after manufacture, define how identification will be retained or transferred to preserve traceability.
Required markings and delivery documents may identify:
Manufacturer and product standard.
Steel grade, PSL and delivery condition.
Outside diameter and wall thickness.
Heat number and pipe or batch identification.
Length and corresponding inspection records.
Illustrative inquiry:
Seamless Steel Line Pipe — API 5L — X52, PSL 2 — Delivery Condition as Specified — OD 168.3 mm × WT 7.1 mm — Fixed Length 12,000 mm — Beveled Ends — 3LPE Coating — Material Certificates and Pipe Tally Required
This example illustrates ordering information, not confirmed availability, pressure capacity or certification. The full grade designation, coating specification and inspection requirements must be completed for the actual order.
Specification compliance and permission to apply an API Monogram are different matters. Where a licensed manufacturer or Monogram is required, include that requirement in the inquiry for verification.
Oil & Gas Gathering Lines
For conveying production fluids between field facilities, subject to the specified service conditions.
Pipeline Transportation
For oil or gas pipeline sections where seamless construction, size and material meet the project requirements.
Facility Connections
For connecting pipework around gathering stations, processing facilities and related equipment.
Pipeline Maintenance & Replacement
For replacement sections matched to the existing design, material and connection requirements.
Is PSL 2 a stronger steel grade than PSL 1?
No. PSL defines the specification level; the steel grade defines strength requirements. Both must be identified.
Can PSL 2 pipe be used for sour service?
Not automatically. State the sour-service requirements, applicable provisions and required testing.
Does a higher X grade guarantee greater pressure capacity?
No. Capacity also depends on wall thickness, temperature, design factors, corrosion allowance and the complete piping design.
Can seamless pipe have welded connections?
Yes. “Seamless” describes the pipe body. Installation commonly includes circumferential field welds.
Can API 5L and ASTM A106 pipe be substituted?
Only after technical review and project acceptance. They address different product requirements and should not be assumed equivalent.
Can you supply coated pipes with end cutbacks?
Include the coating system, thickness, cutback dimensions and inspection requirements in the inquiry. Supply scope will be confirmed during quotation.
What documents should I request?
Identify the required certificate type, test reports, traceability records, coating reports and pipe tally before ordering.
ZSJHSTEEL helps overseas buyers develop clear line-pipe specifications and coordinate sourcing around project requirements.
Our focus is technical communication covering grade, PSL, dimensions, end preparation, corrosion protection and documentation. Packing, identification and delivery arrangements can be agreed during quotation to support receiving checks and installation planning.
Send ZSJHSTEEL your:
Product standard and required edition.
Steel grade, PSL and delivery condition.
Outside diameter, wall thickness and lengths.
Quantity and end-preparation requirements.
Service conditions and supplementary specifications.
Coating system, thickness and end cutback.
Inspection scope, certificate type and traceability requirements.
Delivery destination and target schedule.
Contact ZSJHSTEEL for seamless steel line pipe matched to your pipeline specification and procurement needs.
content is empty!